MATERIAL SAFETY DATA SHEET  Safe-React Formula E 



SECTION 1
--MATERIAL IDENTIFICATION AND USE

MATERIAL NAME: Safe-React Formula E For Etching Concrete
SUPPLIER: Shield Industries Inc, Woodstock , GA
TELEPHONE: 770-517-6869
EMERGENCY: 800-535-5053
HEALTH: 1
FLAMMABILITY: 0
REACTIVITY: 1
PPE: B

SECTION 2--HAZARDOUS INGREDIENTS

None

SECTION 3--PHYSICAL DATA

APPEARANCE: Colorless to Slightly Amber Liquid
% SOLIDS: 60%
SPECIFIC GRAVITY: 1.21
PHYSICAL STATE: Liquid
SOLUBILITY IN WATER: Soluble
BOILING POINT: 100C/212F
ODOR: Mild Odor
pH: 0.7

SECTION 4--FIRE AND EXPLOSION DATA

FLASH POINT: Does NOT ignite
EXTINGUISHING MEDIA: Water spray, carbon dioxide, dry chemical
SPECIAL FIRE FIGHTING PROCEDURES: None
UNUSUAL FIRE AND EXPLOSION HAZARD: At temperatures above 60C/140F acid action on most metals may release hydrogen, a highly flammable and explosive gas.
SPECIAL FIRE FIGHTING INSTRUCTIONS: Evacuate personnel to a safe area. Keep containers cool with water spray. Avoid breathing decomposition products. Wear self-contained breathing apparatus and full body protection.

SECTION 5--REACTIVITY DATA

STABILITY: Stable up to 110C/230F
CONDITIONS TO AVOID: Heating above 110C results in an exothermic decomposition with rapid release of CO2 gas.
INCOMPATIBLE MATERIALS: Avoid contact with oxidizers. This material may be extremely hazardous in contact with chlorates or nitrates. Contact with hypochlorites will produce toxic gases. Contact with alkaline materials will generate heat.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition may yield oxides of carbon, nitrogen, and chlorine. Hydrogen gas may be released upon contact with certain materials.
HAZARDOUS POLYMERIZATION: Will not occur.

SECTION 6--TOXICOLOGICAL PROPERTIES EFFECTS OF ACUTE EXPOSURE

INHALATION: Not a likely route of exposure due to physical properties. Product has a low vapor pressure at room temperature and is not expected to present a significant inhalation hazard under ambient conditions. Product can be irritating to the respiratory tract if inhaled as a mist or if the material is vaporized.
SKIN: Acute exposure is irritating. Non-corrosive to skin: (As defined and tested in accordance with the U.S. OSHA's Hazard Communication Standard, DOT Hazardous Material Regulations, Canada 's WHMIS regulations and TDG Regulations. Classified as a mild skin irritant as per the 1992 OECD Guideline for testing chemicals. Number 404 "Acute Dermal Irritation/ Corrosion.")
EYE: Contact may be painful and irritating.
INGESTION: This product may be harmful or fatal if ingested.
CARCINOGENICITY: Not listed on NTP, IARC, ACGIH.
MUTAGENICITY: This product was found not to be mutagenic when tested by the Ames Assay, (OECD Guidelines for Testing of Chemicals, Sec. 471)

SECTION 7--PREVENTATIVE MEASURES

GLOVES: Use impervious (rubber, nitrile) gloves.
EYE PROTECTION: Use chemical goggles or full face shield.
OTHER PROTECTIVE EQUIPMENT: Eye bath, safety shower, full protective clothing.
RESPIRATORY: Avoid breathing vapor and/or mist.
ENGINEERING CONTROLS: If current ventilation practices are not adequate for minimizing exposures, additional ventilation or exhaust systems may be required.
LEAK AND SPILL PROCEDURE: Small spills may be absorbed with non-reactive absorbent (sand) and placed in suitable, covered, labeled containers. Prevent large spills from entering sewers or waterways. Contact emergency services and supplier for advice.
WASTE DISPOSAL: Review federal, provincial, or state and local government requirements prior to disposal.
STORAGE REQUIREMENTS: KEEP OUT OF REACH OF CHILDREN. Keep container tightly closed. Store in fiberglass, polyethylene, or polypropylene containers. Do not store in metal containers, especially aluminum. Storage in certain metal containers at temperatures above 60C/140F may result in hydrogen gas evolution. Do not store at temperatures above 48C/120F.

SECTION 8--FIRST AID

INHALATION: Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen and seek medical attention.
SKIN: Immediately flush with mild soap and water for 15 minutes. Seek medical attention if irritation develops. Remove contaminated clothing and launder before reuse.
EYE: Immediately flush with water for 15 minutes. Seek medical attention.
INGESTION: Do not induce vomiting. If concsious, give 3-4 glasses of water to dilute and get immediate care.

SECTION 9--REGULATORY INFORMATION

SHIPPING INFORMATION: Not regulated under DOT & TDG
WHMIS CLASSIFICATION: Class D2B
SHIPPED IN: Polyethylene containers.

SECTION 10--PREPARATION INFORMATION

DATE: October 11, 2007
DISCLAIMER: This information is provided to the best of our knowledge and belief, however no representation, warranty, or guarantee is made as to it's accuracy, reliability, or completeness. It is the users responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use. We do not accept liability for any loss or damage that may occur from the use of this information.

Copyright 2006-2008 Shield Industries, Inc.

Shield Industries Home|Safe-React Products Home|About Us|Contact Us

Shield Industries, Inc © 2008, All rights Reserved